Application of Bondcoat wire to shaft for builduptt

1/16 P701 BOND COAT 95/5 NI/AL 33 LB SPOOL

CODE: P701-1/16

$49.50

In stock

Minimum quantity for "1/16 P701 BOND COAT 95/5 NI/AL 33 LB SPOOL" is 33.

Metalink® 701 Ni-Al Bondcoat Wire

Nickel/Aluminum composite wire that provides the ultimate tensile strength bond coat for combustion wire and twin wire arc spraying. Manufactured by a proprietary process that covers a solid nickel core wire with a .015in sheath of aluminum which provides the proper exothermic reaction when sprayed with a combustion gun. Twin wire version employs an aluminum core with slightly more nickel content. 

Advantages:
701 Ni-Al Bondcoat wire sprays at a higher speed compared to the currently available bond coat wires and gives an extremely homogeneous spray pattern. Also unlike wires with Nickel powder cores inside an Aluminum tube, this wire does not spit and sputter during application. Nickel powder core type wires tend to propel unmelted Nickel particles if the Aluminum sheath does not melt and provide the proper Exo-thermic reaction. This cannot happen with 701 Ni-Al Bondcoat wire as the solid Nickel wire cannot shoot out unless it is melted and atomized by the compressed air jet before it is sprayed. This ensures a high tensile strength bond that consistently tests at over 12,000psi - the best in the industry. 

Recommended Spray Parameters
Parameters for Diablo Twin Wire Arc system: 200 Amps @ 27V with 50 to 70 psi Air Pressure utilizing high velocity air cap. 

Parameters For 12M, 14M or equivalent torch: Set Oxygen Regulator at 301b and Acetylene Regulator at 151b. Flow Meter settings: 43 oxy, 39 act, 52 air (as indicated on most flow meters). Adjust feed settings so that wire is melting off approximately 1/4-3/8" in front of the air cap. For other fuel gases, consult spool label. 

Deposit Characteristics
• Typical Hardness HRB 75
• Bond Strength 9000 to 12,000-i-psi
• Deposit Rate 10 lbs /hr/100A
• Deposit Efficiency 70%
• Wire Coverage 0.9 oz/ft2 / m 

Applications
• Bond Coat
• Dimensional Restoration 

Surface Preparation Information Surface should be clean, white metal, with no oxides (rust), dirt, grease, or oil on the surface to be coated. Note: It is best not to handle surfaces after cleaning. Recommended method of preparation is, to grit blast with 24 mesh aluminum oxide, rough grind, or rough machine in a lathe. 

Packaging information Part # Description  
P701A 14ga (1.6mm) 33 LB LLWSpool
P701C .125 (3.2mm) 12.5# spool P701C .125 (3.2mm) 25# spool
1/16 P701 BOND COAT 95/5 NI/AL 33 LB SPOOL

CODE: P701-1/16

$49.50
In stock

Minimum quantity for "1/16 P701 BOND COAT 95/5 NI/AL 33 LB SPOOL" is 33.


1/16 P702 STAINLESS 25# SPOOL

CODE: P702

$13.67
In stock


1/16 P704 ALUMINUM BRONZE 30# SPOOL

CODE: P704-1/16

$24.92
In stock


1/16 P710A-25 CHROME CARBIDE 25#SPOOL

CODE: P710A-25

$26.52
In stock


1/16 P711A-25 TUNGSTEN 25# SPOOL

CODE: P711A-25

$58.05
In stock


1/16 P718 PURE COPPER 25# SPOOL

CODE: P718

$23.19
In stock


1/16 P725A-25 TITANIUM 25#SPOOL

CODE: P725A-25

$173.62
In stock


1/16 P756A ONESTEP STEEL 25# SPOOL

CODE: P751A

$19.35
In stock


1/16 P760-25 ULTRAGRIP 25#SPOOL

CODE: P760-25

[Contact us for a price]
In stock


1/16 P761-33 ULTRAROLL GRIP 33#SPOOL

CODE: P761-33

[Contact us for a price]
In stock


1/16 P790A-25 MORPHALLOY 90 25#SPOOL

CODE: p790A-25

$41.29
In stock


1/16 P795A-25 MORPHALLOY 50 25#SPOOL

CODE: p750A-25

$36.95
In stock


1/8 ALUMINUM 1100 P781C-50 2x25# COIL

CODE: P781C-50

$5.10
In stock


1/8 ALUMINUM 1100, P781C-30 30#SPOOL

CODE: P781C-30

$5.29
In stock


1/8 ALUMINUM 1350, P780C-30 30#SPOOL

CODE: P780C-30

$4.23
In stock


1/8 P703C HARD STAINLESS 50# COIL

CODE: P703

$13.90
In stock


1/8 P704 ALUMINUM BRONZE 25# SPOOL

CODE: P704-1/8

$24.92
In stock


1/8 P720C ULTRA MOLY 30#COIL

CODE: P720C

$71.59
In stock


3/16 ALUMINUM 1100 P781E-30 30#SPOOL

CODE: P781E-30

$4.23
In stock


3/16 ALUMINUM 1100 P781E-50 2x25#COIL

CODE: P781E-50

$5.19
In stock


3/16 ALUMINUM 1350 P780E-30 30#SPOOL

CODE: P780E-30

$4.60
In stock


Anti-Seize Dispenser Pump Brush

CODE: EQ001

$29.60
In stock


Anti-Seize Lubricant

CODE: CH122

$19.89
In stock


BLU-GOO SUPER SEALANT/LUBRICANT

CODE: ML013

$435.00
In stock


Brushable Ceramic

CODE: ML406

$2,150.00
In stock


Brushable Ceramic X.H.D.

CODE: ML408-QT

$174.00
In stock


Ceramic Bead Polymer

CODE: ML355

$89.00
In stock


Concrete Patch

CODE: ML820

$290.00
In stock


Concrete Primer and Sealer

CODE: ML819

$449.00
In stock


Diablo Twin Wire Arc Thermal Spray System

CODE: P9000

$25,000.00
In stock


Epoxy Sticks

CODE: ML001 - ML004

$17.99
In stock

Please, select one


Machinable Repair Compound

CODE: ML400

$950.00
In stock


Metalink 11M Combustion Wire Thermal Spray Gun

CODE: P700011M

$4,100.00
In stock


Metalink 12M Combustion Wire Thermal Spray Gun

CODE: P700012M

$4,585.00
In stock


Metalink 14M Combustion Wire Thermal Spray Gun

CODE: P700014M

$4,880.00
In stock


Metalink 5000 Torch Gun

CODE: P5000

$1,799.00
In stock


Metalink Complete Thermal Spray Outfit

CODE: P7000TSAKT

[Contact us for a price]
In stock


Metalink Fusion Torch

CODE: P600

$1,499.00
In stock


Metalink Sonicoat

CODE: P8000

[Contact us for a price]
In stock


MetalPrep II - Hight Purity Safety Solvent
$9.50
In stock


MultiJet Spray Gun

CODE: P8001

$6,289.00
In stock


RTV Silicones

CODE: ML652

$12.99
In stock


Seal Skin Pipe Wrap

CODE: ML450

$154.00
In stock


Slip-Not

CODE: ML800

$1,235.00
In stock


The Pipe Tourniquet

CODE: EQ003

$24.00
In stock


Top Coat

CODE: ML801

$274.00
In stock


Top Coat XHD

CODE: ML805

$298.00
In stock


Trowelable Ceramic Polymer

CODE: ML410

$275.00
In stock


Uni-Spray-Jet Gun Kit

CODE: P5001KT

$6,160.00
In stock

Type the characters you see in the picture above.

Loading...